上海尊龍凱時生物科技有限公司 www.ruianjituan.com
人載脂蛋白 E 定量分析酶聯免疫檢測試劑盒
本試劑盒僅供科研使用 。用於體外定量檢測人血清 、血漿或細胞培養上清液中的載脂蛋白 E 濃度 。使用前請仔細閱讀說明書並檢查試
劑組分是否完整 。如有產品包裝破損或質量投拆 ,請在收到貨一個月之內聯係尊龍凱時 。
載脂蛋白 E 簡介 :
載脂蛋白 E ,是一個低密度脂蛋白 ,極低密度脂蛋白 ,高密度脂蛋白及乳糜的基本構成蛋白 ,是一個糖蛋白 。成熟的載脂蛋白 E 的分
子量為 34 千道爾頓 。主要由肝細胞 ,巨噬細胞及神經係統中非神經細胞產生 。
載脂蛋白 E 能夠抑製 TNF-α ,Toll 樣受體 3 和 Toll 樣受體 4 介導的炎症反應 ,刺激和調整 T 細胞及增強 M2 型巨噬細胞的抑製炎症作
用 。載脂蛋白 E 在澱粉類代謝中起重要作用 ,在阿爾茨默氏病的發生中起重要作用 。
檢測原理:
本試劑盒采用雙抗體夾心ELISA法檢測樣本中載脂蛋白E的濃度 。載脂蛋白E捕獲抗體已預包被於酶標板上 ,當加入標本或參考品時 ,
其中的載脂蛋白E會與捕獲抗體結合 ,其它遊離的成分通過洗滌的過程被除去 。當加入生物素化的抗人載脂蛋白E抗體後 ,抗人載脂蛋白E
抗體與載脂蛋白E接合 ,形成夾心的免疫複合物 ,其它遊離的成分通過洗滌的過程被除去 。隨後加入辣根過氧化物酶標記的親合素 。生物素
與親合素特異性結合 ,親合素連接的酶就會與夾心的免疫複合物連接起來 ;其它遊離的成分通過洗滌的過程被除去 。最後加入顯色劑 ,若
樣本中存在載脂蛋白E將會形成免疫複合物 ,辣根過氧化物酶會催化無色的顯色劑氧化成藍色物質 ,在加入終止液後呈黃色 。通過酶標儀檢
測 ,讀其450nm處的OD值 ,載脂蛋白E濃度與OD450值之間呈正比 ,通過參考品繪製標準曲線 ,對照未知樣本中OD值 ,即可算出標本中載脂蛋
白E濃度 。
人載脂蛋白E定量分析酶聯免疫檢測試劑盒組成:
組分 規格(96T/48T)
人載脂蛋白E預包被板 12條/6條
5×標準品稀釋液 20ml/10ml
人載脂蛋白E標準品 2/1支(凍幹)
人載脂蛋白E生物素化抗體 10ml/5ml
親和素連接的HRP酶 10ml/5ml
濃縮洗滌液 20× 30ml/15ml
TMB底物 10ml/5ml
中止液 5ml/3ml
封板膠紙 3/2張
說明書 1份
標本收集:
1.標本的收集請按下列流程進行操作 ;
A.細胞上清標本離心去除懸浮物後即可 ;
B.血清標本應是自然凝固後 ,取上清 ,避免在冰箱中凝固血液 ;
C.血漿標本 ,推薦用EDTA的方法收集 ;
D.若待測樣本不能及時檢測 ,標本收集後請分裝 ,凍存於-20℃ ,避免反複凍融 。
2.血清標本不應添加任何防腐劑或抗凝劑 ;
3.標本應清澈透明 ,檢測前樣本中如有懸浮物應通過離心去除 。
4.請勿使用溶血 ,高血脂或汙染的標本檢測 ,否則結果將不準確 。
注意事項:
1.試劑盒請保存在2~8℃ 。
2.濃縮洗滌液因在低溫下可能有結晶 ,請水浴加熱使結晶完全溶解後再配製工作液 。3.標準品複溶加樣後 ,剩餘部份請丟棄 。
4.底物請勿接觸氧化劑和金屬 。
5.加樣時 ,請及時更換槍頭 ,避免交叉汙染 。
6.嚴禁混用不同批號的試劑盒組份 。
7.充分混勻對保證反應結果的準性很重要 ,在加液後請輕輕叩擊邊緣以保證混勻 。
8.室溫反應 ,請嚴格控製在25-28℃ 。
9.洗滌過程是至關重要的 ,洗滌不充分會使精確度下降並導致結果誤差較大 。
10.試驗中標準品和樣本檢測時建議作雙複孔 。
11.加樣過程中避免氣泡的產生 。
12.血清和血漿標本的檢測時 ,檢測抗體的孵育時間應適當延長
檢測前準備工作:
1.試劑盒自冰箱中取出後應置室溫(25-28℃)平衡20分鍾 ;每次檢測後剩餘試劑請及時於2~8℃保存 。
2.將濃縮洗滌液用雙蒸水或去離子水稀釋(1份加19份水) 。
3.如有5X標準品稀釋液 ,請按所需量用雙蒸水或去離子水稀釋(1份加4水) 。
4.標準品: 按標簽複溶體積加入標準品稀釋液複溶使載脂蛋白E終濃度達到4000pg/ml ,室溫反應 ,請嚴格控製在25~28℃ ,靜置15~20分鍾
後輕輕混懸(建議抽吸幾次)待徹底溶解 ,用標準品稀釋液倍比梯度稀釋後依次加入檢測孔中 。(標準曲線取七個點 ,最高濃度為4000 pg/ml,
標準品稀釋液直接加入作為0濃度.)
洗滌方法:
自動洗板機或人工洗板 :每孔洗滌液為300ul ,注入與吸出間隔15-30秒 。洗板5次 。最後一次洗板完成後將板倒扣著在厚吸水紙上用力拍幹 。
實驗過程需自備的材料 :
1.不同規格的加樣槍及相應的槍頭 ;
2.酶標儀 ;
3.自動洗板機 ;
4.去離子水或雙蒸水 ;
操作步驟:
1.通過計算並確定一次性實驗所需的板條數 ,取出所需板條放置在框架內 ,暫時用不到板條請放回鋁箔袋密封 ,保存於4℃ 。
2.建議設置本底較正孔 ,即空白孔,設置方法為該孔隻加TMB顯色液和中止液 。每次實驗均需做標準品對照並畫出標準曲線 。
3.分別將標本或不同濃度標準品(100ul/孔)加入相應孔中 ,用封板膠紙封住反應孔 ,室溫(25-28℃)孵育120分鍾 。血清血漿 ,1500~6000
倍稀釋 ,如無明確範圍 ,可從3000倍開始 。尿樣無需稀釋 ,細胞上清 ,1~15倍稀釋 ,可從2倍開始 。
4.洗板5次 ,且最後一次置厚吸水紙上拍幹 。
5.加入生物素化抗體工作液(100ul/孔) 。用封板膠紙封住反應孔 ,室溫(25-28℃)孵育60分鍾 。
6.洗板5次 ,且最後一次置厚吸水紙上拍幹 。
7.加入親和素連接的HRP酶工作液(100ul/孔) 。用封板膠紙封住反應孔 ,避光室溫(25-28℃)孵育20分鍾 。
8.洗板5次 ,且最後一次置厚吸水紙上拍幹 。
9.加入顯色劑TMB100ul/孔 ,避光室溫(25-28℃)孵育20分鍾 。
10.加入中止液50ul/孔,混勻後即刻測量OD450值 。
結果判斷:
1.複孔的值在20%的差異範圍內結果才有效 ,複孔的值平均後可作為測量值 。
2.每個標準品或標本的OD值應減去本底校正孔的OD值 。
上海尊龍凱時生物科技有限公司 www.ruianjituan.com人的載脂蛋白E參考標準曲線
0
0.5
1
1.5
2
2.5
3
3.5
0 125 250 500 1000 2000 4000
濃度(pg/ml)
O
D值
上海尊龍凱時生物科技有限公司 www.ruianjituan.com
3.手工繪製標準曲線 。以標準品濃度作橫坐標 ,OD值作縱坐標 ,以平滑線連接各標準品的坐標點 。通過標本的OD值可在標準曲線上查出其
濃度 。
4.若標本OD值高於標準曲線上限,應適當稀釋後重測 ,計算濃度時應乘以稀釋倍數 。
典型數值和參考曲線
濃度pg/ml 典型OD值1 典型OD值2 OD平均值
0 0.097 0.109 0.103
125 0.186 0.202 0.194
250 0.287 0.303 0.295
500 0.512 0.56 0.536
1000 0.858 0.89 0.874
2000 1.623 1.707 1.665
4000 2.941 3.085 3.013
人載脂蛋白E參考標準曲線
靈敏度 ,特異性和重複性:
1.靈敏度 :多次重複結果表明 ,最小檢出量為79.6pg/ml 。
2.特異性 :與人的ApoA1 、ApoA2 、ApoB 、ApoB100 、ApoC1 、ApoC2 、ApoD等沒有交叉反應。
3.重複性 :板內 ,板間變異係數均<10%.
參考文獻:
1. Mullick, A.E. et al. (2007) Arteriosescler. Throm. Vasc. Biol. 27:339
2. Perugini, M.A. et al. (2000) J. Biol. Chem. 275:36758.
3. Krimbou, L. et al. (2004) J. Lipid. Res. 45:839.
4. Baitsch, D. et al. (2011) Arteriosescler. Throm. Vasc. Biol. 31:1160.
5. Jones, P.B. et al. (2011) PLoS ONE 6:e14586.
6. Chroni, A. et al. (2005) Biochemistry 44:13132.上海尊龍凱時生物科技有限公司 www.ruianjituan.com
ELISA Kit for the Quantitative
Analysis of Human Apolipoprotein E
The human Apolipoprotein E ELISA (enzyme-linked immunosorbent assay) kit is used for detection of human Apolipoprotein E in cell
culture supernatants,human serum and plasma.THE ELISA KIT IS FOR RESEARCH USE ONLY. Please read this instruction manual
carefully and check out the material provided before use, and you can contact with our company if any questions. You can enter our
website or call us for other aim.
Introduction
ApoE, a glycoprotein, is a structural component of serum LDL, VLDL, HDL, and chylomicrons. Mature human ApoE is a 34 kDa
protein. It is produced predominantly by hepatocytes, macrophages, and non-neuronal cells in the central nervous system.
ApoE suppresses TNF-α , TLR3, and TLR4 mediated inflammation and promotes the development of regulatory T cells and
anti-inflammatory M2 macrophages. ApoE also plays a critical role in amyloid metabolism and the development of Alzheimer’s disease.
Principles of the Test
The kits is a solid sandwich enzyme-linked immunosorbent assay for detection of human Apolipoprotein E. An anti-human
Apolipoprotein E monoclonal antibody has been absorbed onto the wells of the microtiter strips provided. Samples including specimens
or standards were pipetted into wells. The human Apolipoprotein E in specimens or standards would be captured by the coated antibody
and the free others were removed by washing. The human Apolipoprotein E biotin-conjugated antibody were added and binds to human
Apolipoprotein E captured by the first antibody, which formed a sandwich. Streptavidin-HRP would be added and binds to the biotin
conjugated antibody, then free Streptavidin-HRP would be removed during a wash step. After this, subtrate solution would be added and
catalyzed by the HRP, and a coloured product is formed. The intensity of the colored product is used to calculate in proportion to the
amount of human Apolipoprotein E in the original specimen.
Materials provided with the kits:
Reagent 96/48Test Kit
Human Apolipoprotein E
Antibody-Coated Wells
12 strips/6 strips
5×Standard Diluent 20ml/10ml
Human Apolipoprotein E Standard 2/1vial(s)
Human Apolipoprotein E Detetion
Antibody
10ml/5ml
Streptavidin-HRP 10ml/5ml
Wash Buffer Concentrate 20× 30ml/15ml
TMB 10ml/5ml
Stop Solution 5ml/3ml
Plate Covers 3/2
Complete Instruction Manual 1
Specimen Collection
1.Collecting specimen as following:
A.The particulate of the cell culture supernatants should be removed before use.
B.Serum was obtained from clot at room temperature.
C.Please collect plasma with EDTA.
D.Assay immediately or store samples at -20℃. Avoid free-thaw cycles.
2. Antiseptic and anticoagulant should not appear in Serum samples.
3. Any particulate should be removed from samples before use.4. Do not use grossly hemolyzed or lipemic samples.
Note: Strongly recommend that the serum and plasma samples should be diluent as doubling dilution before use.
Precautions for use:
1.Please storage the Kit at 2~8℃ 。
2. Washing buffer concentrate may have crystal in low temperature, and you can melt its in water-bath before use.
3. Please discard the remains after use of the dissolved standard.
4.Avoid contact of substrate solution with oxidizing agents and metal.
5.Usage of disposable pipette tips avoid microbial contamination or cross-contamination of reagents or specimens.
6. Do not mix or substitute reagents with those from other lots or other sources.
7.To ensure the adequate mixure of added reagents, please tap gently the plate after the wells were filled with liquid.
8. Incubation temperature should be 25~28℃.
9. Wash step was crucial for whole assay process.
10. Duplicate wells of the same sample were recommended in assay process.
11. Avoid the foam while pour the liquid into wells.
12.For serum or plasma samples ,the biotin-conjugated antibody should be incubate for at least 90 minutes.
Reagent Preparation
1.The reagents should be warmed up to room temperature before use. The remanent reagents must reseal and put into refrigeratory
again as soon as possible.
2.Dilute 1ml of wash buffer Concentrate into 19ml deionized or distilled water to work.
3. If you have a 5x standard diluent, please dilute it with double steaming water or deionized water.
4. Add standard diluent to the bottle according to the volume of the label and wait 15 minutes for complete dissolution. Incubation
temperature should be 25~28℃. 。And in turn add the half concentration diluent by standard diluent .
Wash step:
Automated microplate washer or operating by pipette: Each well should be pour into 300ul wash buffer and soak 15 or 30 seconds,then
be aspirated, five times process were repeated. After the last wash, remove remaining wash buffer by aspirating. Invert the plate and blot
it against clean paper towels.
Materials Required But Not Provided
1. pipettes and pipette tips
2. Microwell strip reader capable of reading at 450 nm (540 nm as optional reference wave length)
3. automated microplate washer
4.Glass-distilled or deionized water
Assay procedure
1.The needed strips were putted into the frame, the remains were returned into foil pouch and resealed.
2.Blank well were recommended, which only color reagent and stop solution be added. It is suggested that each testing with gradient
density of standard for standard curve.
3.Add 100ul of standard or sample.Cover with the Plate Covers provided.Incubate for 2 hours at room temperature. If the serum or
plasma sample,you should diluent from 1500 to 6000 times,you can start with 3000times diluent while have no scope.If the cell culture
supernatants,you should diluent 2 times for the assay or diluent further more.
4.Five times wash process were repeated.
5.Add 100ul of detetion antibody. Cover with the Plate Covers provided.Incubate for 1 hour at room temperature.
6.Five times wash process were repeated.
7.Add 100ul of Streptavidin-HRP. Cover with the Plate Covers provided. Lucifugal incubation for 20 minutes at room temperature.
8.Five times wash process were repeated.
9.Add 100ul of TMB ,Lucifugal incubation for 20 minutes at room temperature.
10.Add 50ul of stop solution to each well, determine the optical
density of each well within 10 minutes.
上海尊龍凱時生物科技有限公司 www.ruianjituan.comHuman Apolipoprotein E Standard Curve
0
0.5
1
1.5
2
2.5
3
3.5
0 125 250 500 1000 2000 4000
Apolipoprotein E Concentration(pg/ml)
O
p
t
i
c
a
l
D
e
n
s
i
t
y
上海尊龍凱時生物科技有限公司 www.ruianjituan.com
Calculation of Results
1.Duplicates should be within 20 percent of the mean. Average absorbance values for each set of duplicate samples were used as
detection results.
2.The blank absorbance values of subtract should be deducted.
3.Drawing a best fit curve through the points of graph. Draw the standard curve by plotting assayed OD valure (on the Y axis) vs.
concentration (on the X axis). The sample concentration was obtained based on its OD value founding in the standard concentration
curve.
4.If the values obtained are not within the expected range of the standard, Samples should be dilute and assay again.
Typical Data and Standard Curve
Concentrati
on
(pg/ml)
Typical data
1
Typical data
2
Average
0 0.097 0.109 0.103
125 0.186 0.202 0.194
250 0.287 0.303 0.295
500 0.512 0.56 0.536
1000 0.858 0.89 0.874
2000 1.623 1.707 1.665
4000 2.941 3.085 3.013
Human Apolipoprotein E Standard Curve
Sensitivity,Specificity, Repeatability
Sensitivity: repeated assays were evalsuated and the minimum detectable dose was 79.6pg/ml.
Specificity: No significant cross-reactivity or interference with human ApoA1 ,ApoA2,ApoB ,ApoB100 ,ApoC1, ApoC2,ApoD.
Repeatability: The coefficient of variation between wells or plates is less than 10 per cent.
REFERENCES:
1. Mullick, A.E. et al. (2007) Arteriosescler. Throm. Vasc. Biol. 27:339
2. Perugini, M.A. et al. (2000) J. Biol. Chem. 275:36758.
3. Krimbou, L. et al. (2004) J. Lipid. Res. 45:839.
4. Baitsch, D. et al. (2011) Arteriosescler. Throm. Vasc. Biol. 31:1160.
5. Jones, P.B. et al. (2011) PLoS ONE 6:e14586.
6. Chroni, A. et al. (2005) Biochemistry 44:13132.
貨號 | 產品名稱 | 規格 | 價格 | 指令 |
HME031 | 人載脂蛋白 E 定量分析酶聯免疫檢測試劑盒 | ¥0.00 | 放入購物車 》 | |
HME03 | 人載脂蛋白 E 定量分析酶聯免疫檢測試劑盒 | ¥0.00 | 放入購物車 》 | |
A19000 | HAKATA DMEM低碳酸氫鈉培養基 | 500ml | ¥250.00 | 放入購物車 》 |
A19512 | HAKATA MEM培養基 | 500ML | ¥70.00 | 放入購物車 》 |
M038 | EL-4小鼠淋巴瘤細胞 | ¥1800.00 | 放入購物車 》 |